Skip to content
Water and heating pipes

Pipework repairs and replacement across Cardiff and South Wales

Leaking, corroded, noisy or burst pipes need attention before they damage your home. Cardiff Plumbing Limited finds the problem, explains your options and fixes it properly — from a pinhole leak to a full pipe run.

  • We locate the fault before we start digging
  • Repair costs shown upfront, no surprises
  • Minimal disruption, tidy work
Warning signs

Seven signs your pipes need a plumber's look

Pipe problems rarely fix themselves. A slow drip in the cupboard under the sink or a stain on the ceiling above it is your signal to act before structural damage spreads or the pipe fails completely.

Damp patches on walls or ceilings

Water escaping from pipes inside the wall or above. The longer it leaks, the more damage to plaster, timber and insulation.

Water pooling or wet carpet

Usually a burst or pinhole leak under the floor. The longer you wait, the more likely mould, rot and structural damage.

Discoloured or stained pipes

Green verdigris on copper, white crusty deposits on chrome, or rust weeping through. The pipe wall is thinning and a leak is likely.

Rattling, banging or hissing sounds

Water hammer from pipes moving loose or water pulsing through a partly blocked line. It stresses the joints and leads to leaks.

Water meter spinning when taps are off

A hidden leak somewhere in your pipes or underground supply. The sooner you find it, the less water you waste and pay for.

Slow drips under sinks and pipes

A weeping joint or corrosion starting. Catch it now and it's a simple repair; leave it and the damage spreads into the cabinet below.

Discoloured water or particles in the tap

Rust or debris from corroding pipes inside. The pipe material is degrading and needs replacement.

What type of pipe do you have?

Copper, plastic (PVC and polybutene), and steel are the common ones. If you're not sure, describe what you see — colour, flexibility, joints — and we'll work out what you've got and what it needs.

Materials and options

Copper, plastic and steel — which lasts longest

The right pipe material depends on what it's carrying (hot water, cold water or heating) and how long you want it to last. Here's the honest comparison.

Copper
The gold standard for water supply and heating. Lasts 50+ years, doesn't degrade in UV light, resists corrosion if the water isn't too acidic. Joins with solder joints or compression fittings, both solid if done right. Costs more upfront but rarely needs replacement. Some areas have soft water that slowly eats through copper; we check if that's your problem.
Plastic (PVC/CPVC)
Used for cold supply and waste. Durable and cheap, unaffected by corrosion. Some older plastic (polybutene) becomes brittle with age and can crack without warning—if that's what you have, replacement is the safest move. Modern PVC is reliable but doesn't suit hot water directly.
Polybutene (PB)
Installed widely in the 1980s and 1990s, this plastic can become brittle and fail without warning. If your house has this, we recommend replacement as a precaution, especially if you've had one burst already.
Steel and galvanised pipes
Stronger than copper for certain applications but prone to rust and corrosion on the inside, especially with hard water. The inside gradually clogs with rust scale, restricting flow. Usually worth replacing rather than cleaning out.
Pushfit plastic systems
Modern PVC and polyethylene pipe that clicks together without soldering. Easy to install, no open flames needed, reliable joints. Good for new runs or replacements where access is tight.

We'll recommend the best material for your water quality, usage and budget. Sometimes a repair works; sometimes full replacement makes sense. We show you the difference in cost and durability.

Microbore and standard pipework

Older systems often ran ½-inch or ¾-inch pipes. Modern microbore systems use narrower tubes and smaller radiators, cutting heat loss and costs. If you're extending or replacing, we can advise whether upgrading makes sense for your property.

What's included

How we repair or replace your pipework

  • Visual inspection of the pipes, joints and surrounding areas
  • Locating the fault (we don't start tearing walls apart without knowing where it is)
  • Isolating the water supply to the damaged section
  • Removing the old, corroded or leaking pipe
  • Cleaning out the area and checking for further damage
  • Fitting new pipe in the same material or upgrading to copper or modern plastic, your choice
  • Proper joints — soldered for copper, compression fittings or pushfit for plastic
  • Flushing the new pipe to clear debris and check for leaks
  • Making good the wall, floor or under-floor area and tidying up
  • Testing water pressure and flow, and showing you the work before we leave

If the pipe is under the floor or inside a wall, we'll discuss access options with you. Sometimes a small section can be exposed minimally; sometimes rerouting makes sense.

How the job works

From your first call to running water again

  1. You describe the problem

    Tell us where the leak or discoloured pipes are. We'll ask about damp patches, water meter readings and what you've noticed.

  2. We locate and quote

    We visit, find the exact fault and explain your options — repair, patch or full replacement. Clear price before we start.

  3. We repair or replace

    Water off, old pipe removed, new pipe fitted with proper joints and tested. The area is made good and tidied.

  4. We hand over

    You run the taps, we show you the work is done, any exposed pipe is labelled and tidy, and you know the problem is solved.

Building regulations and water standards

Pipes must meet the water regs and Building Regs

All replaced and repaired pipework must comply with the Water Supply (Water Fittings) Regulations 1999, Building Regulations Part P (electrical) where relevant, and British Standards for the material used.

That means using approved materials (BS EN standards for copper, plastic and fittings), proper pipe sizing for the flow you need, correct isolation valves, and no contamination risk. For water supply pipes, we use mains-approved material and check that cold water comes from the mains and hot from your system correctly.

If your property is Listed or in a conservation area, certain materials may be preferred—we'll check before recommending.

What affects the cost

Why one pipe job costs more than another

  • Length of pipe to replaceA 2-metre run costs less than 15 metres.
  • Access and locationPipes under the floor, behind walls or under a bath take longer and may need careful routing.
  • The materialCopper costs more than plastic but lasts longer and needs fewer repairs.
  • Existing conditionHeavily corroded or seized joints slow the work down.
  • How much we have to exposeA leaking joint in an accessible pipe is a quick fix; one buried under concrete or inside a wall takes planning.
  • Number of repairs in one visitTackling several pipe faults at once usually saves time and cost.
After the repair

Keeping your pipes in good working order

Bleed air from the system

After a repair, air can get trapped in the pipes. Run the cold taps for a minute to push it through, then hot taps if the repair was on the heating.

Check your water pressure

Low pressure after a repair usually means air in the line. If pressure stays low, we'll check for blockages in the new pipe.

Isolate old damaged sections

If you have polybutene or steel pipes left in the system, fit isolation valves so you can shut them off if they fail.

Know where your stop tap is

Find your main water shut-off and practice turning it, so you know you can stop the water in an emergency.

Maintain your heating system

If the repair was on heating pipes, bleed your radiators and top up the system pressure so it works properly.

Monitor for new leaks

Keep an eye on the repaired area for the first few weeks. A slow seep at a new joint is rare but we'll fix it immediately if it happens.

Questions answered

Pipework repair questions, answered plainly

How do you find a leak if the pipe is under the floor?

We start by looking for damp patches, discoloured flooring or wet carpet, which usually point to the right area. If that doesn't work, we can listen for water escaping (a hissing sound) or use a moisture meter to find the damp. Only as a last resort do we open up the floor—most of the time the visual and acoustic clues are enough. We'll always explain the method before we start.

Can a leaking pipe be repaired or does it always need replacing?

It depends on the fault and the material. A pinhole leak in copper can sometimes be patched with a compression fitting (temporary fix) or a small section can be cut out and spliced in. A weeping joint can be re-soldered. But if the pipe is corroded throughout, pitted or brittle, replacement is safer and lasts longer. We inspect it first and tell you which makes more sense—and what the cost difference is.

What's the difference between copper and plastic pipes?

Copper lasts 50+ years, is unaffected by UV and extremely durable, but costs more. Plastic (PVC) is cheaper and won't corrode, but some older types (polybutene) can become brittle and crack. Modern plastic is reliable for cold water and waste, but we usually recommend copper or modern CPVC for hot supplies because it handles heat better. We'll recommend the right material for your water and your budget.

If I have polybutene pipes, do I need to replace them all?

Polybutene was used widely in the 1980s and 1990s and can become brittle with age. If you've never had a burst, you might be okay for now—but if you've had one, or the pipes are over 25 years old, replacement is a sensible precaution. We can inspect yours and advise. If budget is tight, we can prioritize the most vulnerable sections first.

Will the work damage my walls or floors?

We try to minimize disruption. If the pipe is in an accessible location (under the sink, in an airing cupboard), we can often work without opening walls. If the pipe is buried, we discuss your options first—sometimes a new route around the wall is better than opening it up. We always make good after us, filling holes cleanly so a decorator can finish them. We'll explain the best approach before we commit to anything.

How long does a pipework repair or replacement usually take?

A simple repair (re-soldering a joint, patching a pinhole) might be an hour. A section replacement under the sink or in an accessible pipe is usually a morning's work. If the pipe is under the floor or inside a wall and needs careful routing, it may take longer. We'll give you a realistic timescale when we quote, and keep disruption to a minimum.

Leaking or corroded pipes? We'll find and fix them

A qualified, fully insured plumber will locate the fault, explain what's needed and give you a clear price.

03300437479