Skip to content
Thermostatic and manual valves

Radiator valve replacement across Cardiff and South Wales

A stiff valve, one that leaks at the connection or a radiator you can't control properly. Cardiff Plumbing Limited fits new thermostatic or manual valves so you get even heat and can balance your system. You'll see the price before we start work.

  • Thermostatic or manual, whichever suits your system
  • No draining the whole system if you don't need to
  • Even heat across all your radiators
When valves go wrong

Five signs a radiator valve needs replacing

Most valve problems creep up quietly. A radiator that's warm at the top but cold at the bottom, a hissing sound when you turn the knob, or a small drip at the connection. These are the calls we answer most often.

Stiff or stuck valve

A knob that won't turn or takes real force. Inside, mineral deposits and corrosion have gummed up the piston. Forcing it can snap the valve stem.

Water dripping at the connection

A slow drip where the valve joins the radiator or the pipework below. The seal inside has perished and the valve needs replacing.

Radiator stays cold no matter the setting

The valve piston has stuck in the closed position. Water can't flow through, so the radiator never warms up even when the heating is on.

Hissing or squeaking when you adjust it

Air or corrosion inside the valve. A thermostatic valve (TRV) makes this sound if the sensor element is failing or the valve is about to seize.

One radiator much hotter than the others

If your system is unbalanced, some radiators blaze while others barely warm. A faulty or missing valve on one of them stops you adjusting the flow.

Thermostatic or manual?

A thermostatic radiator valve (TRV) is a temperature sensor in a knob that closes slightly if the room gets warm, cutting flow automatically. A manual valve you adjust by hand. Most homes use TRVs for comfort and to save energy, but older systems or certain rooms (a hallway, a kitchen with a cooker) are better with a fixed manual valve.

Valve types and ratings

How valves differ and what to look for

All radiator valves are rated for a maximum flow, usually 1.5 bar or 2 bar. The rating must match your system pressure, or the valve won't control properly.

Thermostatic radiator valves (TRVs)
A sensor bulb responds to room temperature and adjusts the flow automatically. Good for bedrooms and living rooms. More expensive but saves energy and keeps rooms at different temperatures.
Manual wheel or lever valves
You turn the knob to adjust flow, from fully closed to fully open. Cheap, robust and suited to rooms you don't need to adjust often, like a hallway or airing cupboard.
Lockshield valves
A manual valve with a cap you hide after balancing. Used on the return side of the radiator to set a fixed flow during commissioning, then left alone.
Smart thermostatic valves
WiFi or Bluetooth TRVs you control from your phone or a hub. More convenience but need batteries or a power supply and are pricier.

Look for a valve made to EN 215 (thermostatic) or equivalent, with a pressure rating that matches your system. Quality brands like Danfoss, Caleffi and Comap hold their ratings better than cheap imports.

Fitting straight on old pipework

Most radiator valves sit on a standard 15mm or 20mm copper connection. If the pipework is in good condition and the valve seat is sound, we can often fit a new valve without draining the system. If the pipe is corroded or weeping, we'll replace that section too.

What's included

Everything in a proper radiator valve replacement

  • Visiting to check the valve, the pipework and your system setup
  • Deciding whether the valve can be replaced without draining, or if the system needs draining first
  • Isolating the radiator so water doesn't spill everywhere
  • Carefully unscrewing the old valve and removing any trapped sludge or corrosion
  • Fitting the new valve the right way round (inflow marked with an arrow on many TRVs)
  • Using new PTFE tape and jointing compound to make a watertight seal
  • Opening the bleed valve to let trapped air out
  • Flushing and pressurising the system to check for leaks
  • Testing the valve works and the radiator heats properly
  • Tidying up and checking the boiler is running safely

If the pipework is corroded or weeping, we'll give you a separate quote for new pipe and fittings, usually a small cost on top.

How the job works

From the first call to balanced heating

  1. You ring and describe the problem

    Tell us which radiator is faulty and what it's doing. We'll ask if the system drains easily or if the valve might be blocked.

  2. We inspect and quote

    We look at the valve, the pipework and check the system pressure. You'll know the full price before we turn a spanner.

  3. We replace the valve safely

    Water off at the radiator, old valve out, new one fitted with fresh seals and checked for leaks under pressure.

  4. We test and balance

    Radiator heats properly, air is bled out, and if needed we adjust other valves so heat spreads evenly around the house.

Building Regulations and standards

Valves that meet UK safety requirements

Radiator valves must comply with Building Regulations Part L (Conservation of Fuel and Power) if they're part of a new or upgraded heating system. All radiators in living rooms and bedrooms must have thermostatic valves (unless it's a heat pump system with zone control instead).

We fit valves to EN 215 (thermostatic) or EN 12098 (smart controls), with proper backflow prevention built in. The installation must be safe, the system balanced, and the boiler run a safety check before we leave.

If your system is very old and doesn't have TRVs, upgrading is often worth doing when a valve fails — better comfort and lower bills.

What affects the cost

Why radiator valve jobs vary in price

  • The valve itselfA basic manual valve costs less than a quality TRV or a smart thermostat.
  • Draining the systemIf the valve can be isolated safely, we don't drain. If we do, it takes longer and uses treated water.
  • Stuck or corroded fittingsAn old valve that won't budge takes extra time and care to remove without damaging the pipe.
  • Pipework conditionIf the copper is corroded or weeping, we'll need to replace that section too.
  • How many valvesDoing two or three radiators in one job saves on call-out time and coordination.
  • System balancingIf you want all radiators at the same temperature, we may adjust other valves as well.
Keeping them working

How to look after your new radiator valves

Turn the knob gently

TRV knobs are delicate; don't force them. If a valve sticks, call a plumber rather than breaking the sensor.

Don't cover the sensor

On a TRV, the bulb senses the room temperature. Keep it in the open air, not hidden behind a curtain or a radiator cover.

Check for drips

A small weep where the valve joins the radiator is normal at first, but should stop after a few minutes. If it's still dripping after a day, ring us back.

Bleed air regularly

If a radiator turns noisy, use the bleed valve (a small square key) to let air out. Turn it slowly until water appears, then close it.

Test annually

Once a year, carefully turn the TRV knob through its range to make sure it still moves smoothly and the radiator responds.

Keep the pressure stable

Watch your boiler's pressure gauge; it should stay around 1.0–1.5 bar. If it keeps dropping, there's a slow leak and we should check it.

Questions answered

Radiator valve questions, answered plainly

Can you replace a radiator valve without draining the whole heating system?

Often, yes. If the valve can be isolated safely with its own isolation valve or a lockshield, we can replace it without draining. The small amount of water that escapes when we unscrew the old valve can be caught and the new one fitted quickly. If the system has no isolation valve or the pipework is very corroded, we may need to drain it, which takes longer and costs a bit more.

What's the difference between a TRV and a manual valve?

A thermostatic radiator valve (TRV) has a sensor bulb that closes the valve slightly as the room warms up, automatically reducing heat flow. A manual valve you adjust by hand, turning the knob to increase or decrease flow. TRVs are more convenient and save energy in living rooms and bedrooms. Manual valves are cheaper and suited to rooms like hallways or bathrooms where you don't need to adjust temperature often. Building Regulations require TRVs in most rooms.

Why is my new TRV hissing when I turn it?

A small squeak or hiss from a TRV is usually air being pushed out of the valve as the piston moves. It's normal for the first few adjustments after fitting. If the hissing is loud and ongoing, or the valve is hard to turn, air may be trapped in the system and we may need to bleed other radiators or check the system pressure.

How often should radiator valves be replaced?

A well-made TRV or manual valve can last 10–15 years or longer. If it sticks, leaks or stops working, that's the time to replace it. If your heating system is very old and valves are failing regularly, it may be a sign the system needs a good flush to remove sludge and corrosion.

If I replace one radiator valve, do I need to replace them all?

No. You only replace the valve that's faulty. If your system feels unbalanced after, we can adjust other valves to even out the heat. If multiple valves are sticking or leaking, it's worth replacing them together so you don't have repeat call-outs, and the job is usually more efficient.

Will replacing a radiator valve fix uneven heating?

Sometimes. If one radiator is cold because its valve is stuck or blocked, replacing it should bring that radiator back to temperature. If some radiators are hot and others warm but the valves work fine, the system needs balancing — we adjust the lockshield valve on the return side of each radiator to set the right flow. Both jobs together give you even, comfortable heat throughout the house.

Ready to fix your radiator heating?

A qualified plumber will check the valve and pipe, explain what's needed and give you a clear price before we start.

03300437479