Shower pump installation and repair across Cardiff and South Wales
A shower that trickles when you need it to flow? A pump draws water from your tank or cylinder and gives you the pressure you're after. Cardiff Plumbing Limited fits them, fixes them and makes sure they're the right size for your home.
- Right pump for your water supply
- Installed with isolation valves and check valves
- Tested and balanced before we leave
Five signs a shower pump will help
Not every weak shower needs a pump—sometimes it's a clogged head or a faulty mixing valve. But if the problem is low pressure from your tank or cylinder, a pump is usually the answer. Here's what usually brings us out.
Shower pressure drops when someone uses a tap
Your hot water comes from a tank in the loft and relies on gravity to push it down. When another tap opens, the pressure drops because water is being drawn away. A pump gives you priority to the shower.
Your shower is upstairs and the tank is in the loft
The only water pressure comes from the height of the tank above the shower head. Unless the tank is very high, flow will be weak. A pump puts the pressure where you need it.
Your mixer tap struggles on hot water
When the cold from the mains is strong but hot from the tank is weak, mixing taps can't balance properly. A pump raises the hot side to match.
You've recently changed the boiler or water system
Moving to a combi boiler or mains-only hot water can expose weak pressure in existing pipes and taps. A pump puts right what the old gravity system masked.
Your existing pump has failed or is very noisy
Pumps last 8–12 years. When one wears out, water pressure drops suddenly. A replacement brings back the strong shower you're used to.
If your hot water is from a combi boiler (mains pressure) and your cold is mains, the problem might be a blocked shower head, a faulty mixing valve, or a blockage in the pipework. We'll check those first—a pump solves pressure problems, not blockages.
Shower pumps: how they work and which one you need
Shower pumps come in different sizes and configurations. The right choice depends on how much water you need and where it comes from.
- Single impeller pump
- Boosts pressure on the hot water line only, leaving cold on mains pressure. Best for homes where cold is mains and hot comes from a tank. The pump sits near the hot cylinder.
- Twin impeller pump
- Boosts both hot and cold equally. Used when both supplies come from tanks in the loft, or when you need very strong, balanced pressure. Keeps cold and hot at the same strength.
- Flow-sensing pump
- Runs only when water is being drawn, saving energy. Good if you use the shower for a few minutes daily. Quieter than a continuously running pump.
- Accumulator tank pump
- Includes a small air-pressurised tank that smooths out fluctuations and reduces pump running time. The best option if you want quiet operation and steady pressure under load.
- Utility pump
- A compact, gravity-fed pump that works from low-pressure gravity systems. Fits in tight spaces and is cheaper than larger units, but limited to lower flow rates.
Most homes need a single or twin impeller pump rated 1.5–2.0 bar. For older houses with long pipe runs or multiple bathrooms, we might recommend a larger unit. We'll assess your system and tell you which pump will give you a strong, reliable shower without hammering the pipes.
A pump running in the airing cupboard or utility room can be heard upstairs. We fit isolation mounts and pipe lagging to keep it quiet, and choose flow-sensing or accumulator models if noise is a concern.
Everything in a proper pump installation
- Visiting to look at your water supply and existing pipework
- Choosing the right pump size and type for your system
- Turning off the water and draining the pipes
- Installing isolation valves so the pump can be serviced or replaced later
- Fitting non-return (check) valves to stop backflow
- Connecting the pump to the hot water line with proper flexible hose
- Mounting the pump with vibration isolation to reduce noise
- Lagging pipes to keep the heat in and the noise down
- Testing the system at the shower and all other taps to check for leaks and balance
- Showing you how to use and maintain it
- Taking away old pipes and packaging
If your pump is replacing an old one, we may need to fit new hose connections or update the valves to meet current standards. We'll tell you before we start.
From survey to a strong shower
We survey your system
Looking at your water supply, pipes, tank position and where the pump will sit. We tell you which pump will work best and what it will cost.
We prepare and isolate
Turning off the water and draining the relevant pipes so we can work safely. We fit isolation valves so the pump can be serviced without draining the whole system.
We fit the pump and valves
Installing the pump in the cupboard or plant room, connecting it with proper flexible hose, and fitting check valves to prevent backflow.
We test and balance
Running water through the shower, checking for leaks, and adjusting valves so the pressure is strong and steady. We test other taps too so nothing has changed elsewhere.
Shower pumps and the rules
Shower pumps must have check valves (non-return valves) fitted on each inlet to stop water from flowing backward into the supply pipes. This is a requirement under the Water Supply (Water Fittings) Regulations 1999 and is essential if your pump draws from a tank—it prevents contaminated water from entering the mains.
The pump and all hose connections must be accessible for maintenance and repair. We don't box them in or hide them in a wall—they need to be reachable so an engineer can service or replace them without opening up the structure.
If the pump is on the first floor or above, it must have an overrun pipe connected to it. If water is pushed into the lines faster than the outlet can discharge it, the overrun lets excess water drain safely away (usually to a tray or waste pipe).
Why pump jobs vary in price
- The pump itselfA single impeller is cheaper than a twin impeller or accumulator model. Flow-sensing and quieter units cost more.
- Pipework neededIf existing pipes are corroded or the layout needs changing, new hose and fittings add to the cost.
- Isolation and check valvesNot all homes have them. We fit them as standard, so the pump can be serviced later.
- Access and locationA pump in a tight cupboard or in an awkward position takes longer to fit securely.
- Noise controlVibration mounts and lagging keep it quiet but add a little to the job cost.
- Replacing vs. newRemoving an old pump and refitting in the same location is usually quicker than a new installation.
Pump maintenance and care
Listen for changes
A new pump is fairly quiet. If it starts to rattle, whine or bang, something may be loose or worn. Have it checked before it fails.
Check the overrun
If your pump has an overrun pipe (usually a small plastic tube from the pump to a waste outlet), make sure it's clear and not leaking.
Keep the airing cupboard clear
Pumps need air to cool. Don't block the cupboard vents or pile things against the pump—it will overheat and shut down.
Bleed air if pressure drops suddenly
If water gets in the pump line, air pockets can reduce pressure. The isolation valves have bleed screws—open them gently to let air out.
Service it every 5 years
Some pumps have replaceable filters or seals. Regular servicing catches wear and keeps everything running strong.
Know where your isolation valves are
If the pump stops or leaks, closing the isolation valves lets you turn the water back on elsewhere without losing the whole system.
If the shower needs more than a pump
Bathroom plumbing
Basin, bath, toilet and waste pipes. If your whole bathroom needs plumbing, we design and fit it properly.
Find out more →Shower tray replacement
Cracked, leaking or outdated trays. We remove, fit new ones level, and connect the waste properly.
Find out more →Unvented cylinders
Mains-pressure hot water without a tank in the loft. The best way to get strong showers everywhere, legally and safely.
Find out more →Shower pump questions, answered plainly
Will a shower pump work if my hot water comes from a combi boiler?
No. A combi boiler delivers mains-pressure hot water already. A pump is only needed when your hot water comes from a tank that relies on gravity pressure. If you have a combi and weak shower pressure, the problem is usually a blockage, a faulty mixing valve, or the boiler's output settings. We'll diagnose it correctly before recommending anything.
How much electricity does a shower pump use?
A typical shower pump draws 300–600 watts when running. If you use the shower for 15 minutes a day, that's roughly 1–2 kilowatt-hours per week—a small fraction of your bill. Flow-sensing pumps reduce that because they only run when water is being drawn. We can discuss power options when we quote.
Can I fit a pump myself?
Technically yes, but it needs check valves, isolation valves, proper hose connections and sometimes an overrun pipe. If any part is fitted wrong, water pressure can damage pipes or force contaminated water backward into the mains supply. It's also illegal to do this work without being Gas Safe or qualified in plumbing. We recommend leaving it to a qualified plumber so it's done safely and to regulation.
What happens if the pump stops working?
The shower loses pressure and falls back to gravity pressure only—so it becomes a trickle. That's why we fit isolation valves: you can close them and restore water to the rest of the house while we come to fix or replace the pump. This prevents the whole system from being knocked out by one failed pump.
Will a pump be noisy in the airing cupboard?
New pumps are fairly quiet—a gentle humming sound. We reduce noise by fitting vibration mounts under the pump, lagging the pipes, and sometimes recommending a flow-sensing model that only runs when water is being used. If your airing cupboard is next to a bedroom, tell us and we'll choose the quietest option.
How long does a shower pump last?
Most pumps last 8–12 years with reasonable care. They wear out over time as the impeller and seals degrade, so pressure gradually falls and they may start to rattle. Regular servicing—usually every 5 years—catches problems early. When one fails, it's usually a straightforward replacement if the pipework and valves are still sound.
Ready for a shower you can actually feel?
We'll look at your water system, choose the right pump and fit it with all the valves and isolation you need. Strong pressure, properly installed.
03300437479